clause5.io/ welding/ certified-溶接-inspector

What Is a CWI?

A Certified Welding Inspector holds an AWS credential issued under the QC1 規格. AWS certifies tens of thousands of active CWIs, making it the most widely recognized welding 検査 credential in the industry.

The credential authorizes the holder to perform 目視 inspection of production welds, review WPS and PQR documents for completeness, 確認 that 溶接士 qualifications are current and within their qualified range, and oversee joint preparation and 予熱 prior to welding. CWIs work across 製作 shops, third-party inspection firms, owner's representative organizations, structural engineering firms, and code authorities with enforcement jurisdiction.

The CWI credential is inspection authority. It is distinct from two other AWS credentials that carry different scopes: the Senior Certified Welding Inspector (SCWI), which is a supervisory credential for individuals who manage inspection programs and other CWIs, and the Certified 溶接技術者 (CWEng), which is a design and engineering credential covering WPS development, 継手設計, and engineering judgment on structural 溶接Q&A.

In practice, CWIs verify that fabrication conforms to an approved procedure. CWEngs create and approve the procedure. The roles do not オーバーラップ.

CWI Inspection Scope Under D1.1

D1.1:2025 Clause 8 defines the inspection requirements that structure the CWI's work on a structural welding project. Three clauses establish the core framework.

Clause 8.1.4 sets the qualification baseline for inspection personnel. Inspectors responsible for acceptance or rejection of material and workmanship on the basis of visual inspection must be qualified via one of five enumerated paths. The first path — and the most common on structural steel projects — is current or previous certification as an AWS Certified Welding Inspector (CWI) or Senior Certified Welding Inspector (SCWI) per AWS QC1.

Four alternative paths exist, including CSA W178.2 and ASNT NDT Level II VT. The Engineer may also specify alternative qualifications in the contract documents per Clause 8.1.4.1.

Clause 8.1.5 defines the Inspector's responsibility in full: "The Inspector shall ascertain that all fabrication and erection by welding is performed in conformance with the requirements of the contract documents." This is the operating mandate — every acceptance and rejection decision flows from it.

Clause 8.9 makes visual inspection universal: "All welds shall be visually inspected and shall be acceptable if the criteria of Table 8.1…are satisfied." No production weld is exempt from visual examination. See the full visual 溶接検査 procedure for the complete Table 8.1 breakdown and pre-weld sequence.

Table 8.1 — Eight 外観合格 Criteria

Table 8.1 defines the 受入基準 the CWI applies to every production weld during visual inspection. The eight categories cover every common weld 不連続 encountered in 鉄骨製作.

Beyond visual inspection, D1.1 ties nondestructive 試験 to contract document requirements. Clause 8.16.1 states that 放射線透過試験 (RT) is required "when such inspection is required by the contract documents." Similarly, 超音波探傷試験 (UT) is triggered under Clause 8.19.1 when required by Clause 8.14 — which establishes UT as a contract document requirement. The CWI does not initiate RT or UT independently; the contract documents govern when these methods apply.

AWS CWI Certification

The CWI credential is governed by the AWS QC1 standard and administered by the American Welding Society. It is not part of D1.1 itself — it is an independent credentialing program that specifies exam requirements, eligibility paths, and the certification maintenance cycle. AWS certifies tens of thousands of active CWIs.

Eligibility — Experience Matrix

AWS QC1 defines three education-and-experience paths. The 最小 combination is a high school diploma (or GED) plus 5 years of documented welding-related experience. An associate degree in welding technology reduces the requirement to 2 years, and a bachelor’s degree in engineering or a physical science reduces it to 1 year.

In all cases, experience must be in a welding-related role — inspection, supervision, fabrication, or engineering. Unrelated work does not count toward the eligibility calculation.

The Exam

The certification exam has three parts, with a first-attempt pass rate of approximately 30 to 35 percent. Part A (Fundamentals) is a closed-book exam covering welding processes, metallurgy, 溶接記号, testing methods, and inspection principles.

Part B (Practical Factors) tests hands-on ability to read 溶接記号, interpret blueprint details, and apply inspection measurements. Part C (Code Book) is open-book and tests the candidate's ability to navigate and apply a 溶接コード under time pressure — for structural candidates, this is typically D1.1.

Renewal and Recertification

The CWI credential operates on a 9-year certification cycle, divided into three 3-year periods with renewal applications at years 3 and 6. Over the full 9-year cycle, 80 PDH points are required, with at least 20 PDH earned in the final 3-year period.

At the end of the cycle, CWIs have two recertification options: submit documentation of continued experience plus accumulated PDHs, or retake the certification exam. Allowing certification to lapse requires full re-examination from the beginning.

Related AWS Welding Credentials

The Certified Associate Welding Inspector (CAWI) is an entry-level credential for individuals who work under the supervision of a CWI and are building toward full certification. The Senior Certified Welding Inspector (SCWI) is a supervisory credential for experienced CWIs who manage inspection programs and resolve complex code interpretation questions.

The Certified Welding Educator (CWE) certifies individuals who teach welding in academic or vocational programs. The CWI remains the most widely held and most commonly required credential on structural welding projects.

How Clause5 Supports CWI Workflow

CWIs spend significant time in the field verifying that 施工業者 preheat calls, 入熱 parameters, and material 溶接性 assessments are correct. Clause5 encodes the most commonly referenced D1.1 lookup tables so those verifications happen in seconds rather than minutes of manual table navigation.

Preheat Verification

The preheat lookup table is fully encoded. Enter the steel grade, 溶接工程, and material thickness and get the minimum preheat requirement immediately. Useful when reviewing a contractor's preheat call before welding begins or checking compliance on the shop floor during a visit.

Heat Input Check

The heat input calculation is built in. Enter 電圧, 電流, and 溶接速度 to verify that a WPS heat input limit is being met in production — without doing the arithmetic manually each time.

Carbon Equivalent — Weldability Screen

The Annex B 炭素当量 formula is encoded. Enter the chemistry from the mill test report and get a weldability zone classification before welding begins. Useful when incoming material raises questions about cracking susceptibility.

Symbol Reference

All AWS A2.4 weld symbols with D1.1 cross-references — the same reference set CWIs use when interpreting drawing details in the field.

A Pro Inspector tier is in development, purpose-built for CWI workflow: bulk preheat verification across multiple connections, WPS review tools, and compliance record generation. If you work in welding inspection and want early access, join the waitlist.

API 571 Damage Mechanisms for CWIs

CWIs working in refinery and petrochemical environments encounter damage mechanisms governed by API 571 (Damage Mechanisms Affecting Fixed Equipment in the Refining Industry). While not part of the core CWI exam, understanding these mechanisms is essential for inspectors working in API facilities and is tested on the API 510 and API 570 certifications.

High-温度 hydrogen attack (HTHA). Hydrogen diffuses into 炭素鋼 at elevated temperatures, reacting with carbon to form methane. The methane cannot diffuse out, creating internal voids that lead to fissuring and loss of 機械的性質. CWIs in hydrogen service must monitor for HTHA using specialized UT techniques — conventional UT may not detect early-stage damage.

Creep. Time-dependent deformation of metals under stress at elevated temperatures. Cr-Mo steels (P-Number 4, 5A, 5B) and P91 (P-Number 15E) are used specifically for their creep resistance. CWIs inspecting high-temperature piping must check for creep-induced dimensional changes, surface cracking, and 溶接金属 creep voids.

Stress corrosion cracking (SCC). Austenitic stainless steels (P-Number 8) are susceptible to chloride SCC at temperatures above ~140°F. CWIs inspecting ステンレス鋼 equipment in chloride environments must look for branching transgranular cracks, often starting at weld toes where residual stress concentrates.

Hydrogen-induced cracking (HIC) and sulfide stress cracking (SSC). Carbon steels in wet H2S (sour) service are susceptible to HIC and SSC. CWIs must verify that materials meet NACE MR0175 hardness limits — weld and HAZ hardness typically limited to 248 HV (22 HRC). PWHT is often required to reduce weld hardness below this threshold.

CWI Career Path and Specialization

Entry path. Most CWIs enter through one of three routes: experienced welder transitioning to inspection (most common), engineering degree with welding coursework, or quality technician with hands-on inspection experience. AWS requires a combination of education and experience totaling 3-15 years depending on the education level per QC1.

Endorsements. The initial CWI certification includes one code endorsement — most commonly D1.1 Structural or API 1104 Pipeline. AWS offers 14 endorsements total, and additional endorsements can be added by passing endorsement-specific exams. Common combinations include D1.1 + API 1104 for inspectors working both structural and pipeline projects.

Advanced certifications. CWIs typically add API 510 (pressure vessel inspector), API 570 (piping inspector), or API 653 (tank inspector) as their career progresses. These certifications require the CWI as a prerequisite or equivalent. CWI + API 510 + API 570 is considered the "triple crown" for inspection professionals in the oil and gas sector.

For detailed exam preparation — study plan, three-part breakdown, and test strategies — see the CWI Exam Prep Guide.

On the job, a CWI's responsibilities include reviewing the procedure qualification record to confirm 資格試験 was completed for each procedure, and verifying that welders follow the approved WPS during production — from preheat to パス間温度 to 溶加材 selection.

Key Takeaways

• The CWI is the most widely recognized welding inspection credential — tens of thousands of active CWIs worldwide, required on most structural and pressure equipment projects.
• The CWI exam has three parts — fundamentals (closed book), practical (scenarios), and code book (open book). See the exam prep guide.
• CWI inspection scope under D1.1 spans materials verification, WPS review, 溶接技能者資格, in-process monitoring, visual acceptance per Table 8.1, and NDE oversight.
• API 571 knowledge is essential for CWIs in refinery and petrochemical environments — damage mechanisms like HTHA, creep, SCC, and HIC/SSC require specialized inspection techniques.

"The inspector's job is not to catch every 溶接欠陥 — it's to verify that the contractor's quality system is catching them. The CWI is the last line of defense, not the only one."

— Common AWS CWI exam preparation teaching, aligned with D1.1:2025 Clause 8.1 inspection scope

Reference data from AWS D1.1/D1.1M:2025, AWS QC1, and AWS B5.1. Not affiliated with AWS.