A537 Cl.1/2のSMAW (low-hydrogen)用予熱 — 1-1/2" to 2-1/2"

SMAW (Low-Hydrogen)

Low-hydrogen SMAW (E7018/E7016) uses basic-coated electrodes requiring rod oven storage, assigned to Category B in Table 5.11.

On pressure vessel plate, E7018 is the standard manual electrode for nozzle welds, manhole reinforcements, and repair welding. ASME Section IX procedure qualifications typically require all-weld-metal tensile and guided bend tests. Rod moisture control is critical in vessel fabrication because vessel codes impose stricter hydrogen limits than structural codes.

Why SMAW (low-hydrogen) for A537 Cl.1/2 at 1-1/2" to 2-1/2"

Why SMAW (low-hydrogen) for A537 Cl.1/2 at 1-1/2" to 2-1/2"? SMAW (low-hydrogen) delivers 3-5 lb/hr deposition — compared to SAW at 15-40 lb/hr. Position capability: all positions. Suitability: field and shop.

Filler Metal for SMAW-LH

Electrode: E7018 (AWS A5.1) — the universal low-hydrogen structural rod. Diameter: 1/8" (general/out-of-position), 5/32" (production), 3/16" (heavy plate flat only). Storage: 250°F rod oven minimum per D1.1 §7.3.2.1. Exposure limit: 4 hours out of oven per Table 7.1, then re-bake at 500-800°F for minimum 2 hours per §7.3.2.4 (A5.1 classification).

Typical values for reference — always verify against your approved WPS and electrode manufacturer data.

A537 Cl.1/2

ASTM A537 Class 1 and Class 2 are heat-treated carbon-manganese-silicon steel plates for pressure vessels. Class 1 is normalized (50 ksi yield, 70-90 ksi tensile up to 2.5"); Class 2 is quenched and tempered for higher strength (60 ksi yield, 80-100 ksi tensile up to 2.5"). Both fall under Category B in Table 5.11, requiring low-hydrogen processes for their improved strength and toughness properties. Carbon content is limited to 0.24% max, but the manganese range (0.70-1.35%) and silicon (0.15-0.50%) contribute to a CE-IIW of approximately 0.40-0.46. A537 Class 2 Q&T plates require careful attention to maximum interpass temperature to avoid re-austenitizing the heat-affected zone and degrading the tempered microstructure achieved during mill heat treatment.

A537 Cl.1/2とSMAW-LHでこの予熱が必要な理由

Heat-treated pressure vessel plate with normalized and quenched-tempered options. This steel is prequalified only with low-hydrogen processes under Table 5.11. With SMAW-LH, E7018 low-hydrogen electrodes produce typically 4-8 mL/100g diffusible hydrogen under proper rod oven conditions. The 150°F minimum preheat balances the steel’s strength level and carbon equivalent against the hydrogen control provided by SMAW-LH. Non-low-hydrogen SMAW is not an option for this grade under D1.1 prequalified WPS.

A537 Cl.1/2の代表的な適用例

Applied in cryogenic storage tanks for LNG and liquid nitrogen, elevated-temperature pressure vessels in chemical processing, heavy-wall reactor components, and nuclear containment liner plates. A537 Class 2 quenched-and-tempered plate serves in vessels requiring both high strength and superior impact toughness at sub-zero testing temperatures. Shell course welds and head-to-shell junctions are the primary high-restraint joints where preheat compliance is most critical. Impact testing temperatures for cryogenic service can be as low as -150°F, requiring CVN testing at the design minimum temperature plus a safety margin. The quenched-and-tempered condition of Class 2 means interpass temperature maximums (typically 400-450°F per the qualified WPS) must also be controlled to avoid re-austenitization of the heat-affected zone. Vessel head pressing and spinning from flat plate introduces residual stress concentrations at the knuckle radius that influence the welding sequence for head-to-shell circumferential seams.

1-1/2" to 2-1/2"で予熱が重要な理由

Heavy plate with significant restraint and thermal mass — preheat is critical to maintain slow cooling for hydrogen escape.

SMAW (low-hydrogen)と1-1/2" to 2-1/2"における他の鋼材

A537 Cl.1/2とSMAW (low-hydrogen)

別の組み合わせを試す

インタラクティブ予熱計算機を使用して、D1.1:2025 表5.11のあらゆる鋼材・プロセス・板厚の組み合わせを検索できます。

A537 Cl.1/2溶接ガイド