Préchauffage M270M Gr.345 — H4, Low HI, 20–40 mm: 150°F

M270M Gr.345 / M270 Gr.50

AASHTO M270M Gr.345 (M270 Gr.50) is the standard bridge plate and shape grade with 345 MPa (50 ksi) minimum yield, corresponding to ASTM A709 Gr.50. It is the baseline strength for modern highway bridge design per AASHTO LRFD. Used for plate girder flanges, webs, floor beams, cross-frames, and splice plates. Flanges on large plate girders routinely reach 50–75 mm (2–3 in) thick, making preheat compliance at upper thickness tiers a significant production consideration. NFC preheat per Table 6.3 Group 1; FC per Tables 12.4/12.5.

Comprendre le Préchauffage FC pour M270M Gr.345 / M270 Gr.50

Standard 345 MPa (50 ksi) bridge plate for girders and floor beams. Under D1.5 fracture-critical requirements (Clause 12), the combination of H4 hydrogen designation and this heat input band requires 150°F minimum preheat at 20–40 mm (3/4–1½ in). Lower hydrogen levels (H4 < H8 < H16) allow lower preheat because less hydrogen enters the weld deposit. Similarly, higher heat input reduces preheat requirements because slower cooling rates give hydrogen more time to diffuse out.

Où M270M Gr.345 / M270 Gr.50 est Utilisé

Standard for highway bridge plate girder flanges, box girder webs, cross-frame angles, bearing sole plates, and splice plates in bolted-welded connections. Gr.345 (50) is the baseline strength for modern AASHTO LRFD bridge design. Flange butt splices, web-to-flange continuous fillet welds, and bearing stiffener clips are the dominant weld types in girder fabrication. Girder flanges typically range from 20 to 75 mm (3/4 to 3 in) thick with widths from 300 to 750 mm (12 to 30 in), requiring extended preheat soak times on thicker flange splices.

Contrôle d'Hydrogène H4 pour M270M Gr.345 / M270 Gr.50

Gr.345 (50) with H4 consumables achieves the lowest FC preheat requirements available for the workhorse bridge grade. On girder fabrication lines producing 50–100 meters of flange-to-web fillet weld per shift, the reduced preheat from H4 translates directly to faster welding speed and lower fuel costs for preheat maintenance.

Pourquoi le Préchauffage est Important à 20–40 mm (3/4–1½ in)

Material from 20 to 40 mm (3/4 to 1-1/2 in) includes many girder web plates, splice plates, and bearing stiffener plates. Preheat increases to 20°C (70°F) for Group 1 and 50°C (125°F) for Group 2 under Table 6.3. The thicker section slows hydrogen diffusion, requiring higher preheat to maintain safe cooling rates.

M270M Gr.345 / M270 Gr.50 à 20–40 mm (3/4–1½ in)

At 20–40 mm, Gr.345 (50) serves splice plates, web plates, and bearing sole plates in standard highway bridge girders. CJP butt welds at flange splices are the most critical joint at this thickness — full-penetration ultrasonically-inspected joints that must pass D1.5 acceptance criteria. Preheat compliance is production-critical: 70°F minimum means heated fabrication bays in northern climates during winter bridge contracts.

Consommables Certifiés H4 pour Soudage FC de Ponts

Le désignateur supplémentaire H4 certifie que le consommable dépose au maximum 4 mL d'hydrogène diffusible par 100g de métal déposé. Pour fracture critique M270M Gr.345 / M270 Gr.50 à 20–40 mm (3/4–1½ in) d'épaisseur avec apport de chaleur 1.2–2.0 kJ/mm, les consommables H4 atteignent le préchauffage le plus bas de 150°F (70°C) dans les tableaux FC.

Autres Aciers de Pont à H4 1.2–2.0 kJ/mm · 20–40 mm (3/4–1½ in)

M270M Gr.345 / M270 Gr.50 à H4 1.2–2.0 kJ/mm

Essayez Différentes Combinaisons

Utilisez le Calculateur de Préchauffage D1.5 pour Ponts pour consulter tout acier AASHTO M270, niveau d'hydrogène et combinaison d'apport de chaleur. Voir aussi le Calculateur de Préchauffage D1.1 pour l'acier de construction.

Guides Associés